Aktualności
Single-post vs double-post PV structures. What is the difference and which to choose?

The difference comes down to the static scheme. A single-post structure rests the PV table on one row of posts, while a double-post structure rests it on two. The single-post version is cheaper and faster to install, the double-post version is more stable and better under heavy loads. The choice depends mainly on the wind and snow zone, ground conditions, and the size of the installation.
Single-post vs double-post structure. Where the difference lies
The difference is not the number of posts, but how loads are carried. In a single-post structure the whole table rests on one row of piles. The bending moment from wind and the weight of the modules concentrates at a single support point, which means a higher load on the individual pile and higher requirements for its anchoring in the ground. In a double-post structure the forces are distributed across two rows of supports, so each pile carries less and the whole table works more stably.
This is the right selection criterion. Unit price and installer habit are secondary to how the structure behaves under load at a given site.
Single-post structure. Advantages and limitations
A single-post PV structure supports the modules on a single row of posts driven into the ground. Its strengths are:
- lower steel use and fewer piles,
- shorter installation time and less interference with the terrain,
- lower cost in favorable conditions,
- a simple, repeatable geometry, convenient for farms and phased expansion.
The limitations come from the concentration of loads. A single-post PV structure requires precise selection of cross-sections and an adequate pile embedment depth to keep the table rigid. It is also often limited by module length and is less forgiving of installation errors. It works best on load-bearing ground and under moderate wind and snow loads.
Double-post structure. Advantages and limitations
A double-post PV structure rests the table on two rows of supports. As a result:
- loads are distributed across two points, and each pile is less loaded,
- the whole structure is more stable and has a greater load-bearing reserve,
- it handles heavy wind and snow loads and more difficult ground better,
- it allows greater tolerance for assembly deviations and longer modules.
The price for this is higher material use, more anchoring points, higher cost, and longer installation. A double-post PV structure is the typical choice where the safe operation of the table matters, that is, in demanding climate zones and for large installations. A freestanding double-post structure is also a common solution for larger ground fields.
Which to choose? Decision factors
The choice between a single-post and a double-post structure rests on several parameters:
| Criterion | Single-post structure | Double-post structure |
| Number of support rows | one | two |
| Steel use and number of piles | lower | higher |
| Installation time | shorter | longer |
| Stability and load-bearing reserve | lower | higher |
| Wind and snow loads | moderate | heavy |
| Load on a single pile | higher | lower |
| Cost | lower | higher |
| Typical application | load-bearing ground, repeatable farms | difficult terrain, heavy loads, large tables |
In practice you start from the wind and snow zone for the given location and from a ground survey, and only then select the structural scheme and cross-sections. Cost is best measured per kWp, not as the price of a single component.
The most common mistake in the choice
The most common mistake is choosing a structure by unit price or by the crew’s habit, rather than by the static scheme and site conditions. Saving on profile thickness or embedment depth reduces the safety margin, and a ground installation is fully exposed to wind. The biggest risk here is not the number of panels, but a mismatch between the structure, the ground, and the zone.
Choosing a structure for a specific project
Enzeit Technik manufactures steel double-post structures for ground-mounted PV installations, suited to sites where load-bearing margin and table stability matter in demanding wind and snow zones. The selection path depends on the scale of the investment. For smaller installations in the micro segment, the installer selects the structure in the Enzeit Mount Maker configurator. Farms and large ground installations are run as an individual project, overseen from start to finish by an Enzeit engineer. Are you an investor? Contact us and we will point you to the right path and structure selection for your site.
FAQ
What is the difference between a single-post and a double-post structure?
The number of support rows and how loads are carried. A single-post structure rests the table on one row of piles, a double-post structure on two, which gives greater stability.
Which structure is cheaper?
Usually the single-post one, because it uses less steel and needs fewer piles. In difficult conditions the difference shrinks, because the single-post version needs stronger foundations.
Which structure is better for a high snow zone or weak ground?
Usually the double-post one, because it distributes loads across two rows of supports and has a greater load-bearing reserve.
Is a single-post structure suitable for a PV farm?
It is used on farms with a repeatable layout, mainly for the fast installation. However, it works only on load-bearing ground and under moderate wind and snow loads. In demanding climate zones and where the ground is fully exposed to wind, especially at larger scale, a double-post solution with a greater load-bearing reserve is more commonly chosen.
How do I choose a structure for my plot?
Start from the wind and snow zone and a ground survey, then select the scheme and cross-sections. It is best settled with an installer or directly with the structure manufacturer.